Affiliate Disclosure: This page contains affiliate links. If you purchase through these links, I may earn a small commission at no extra cost to you. As an Amazon Associate, I earn from qualifying purchases. I also earn a commission on purchases made through my Walmart links.
Quick answer: When an aquarium water pump or powerhead stops, check three things before you buy a new one: the power (outlet, power strip or a tripped GFCI), the impeller (stuck or packed with gunk), and the intake (a clogged screen, sponge or tubing). Those three fix most “dead” pumps in a few minutes. If the pump still won’t run, or it hums and gets hot with a clean impeller, replace it. The motor is sealed, so there’s nothing inside to repair.
From My Store: I Just Bought New Ones
I never tried fixing water pumps. When one quit, I just bought a new one. Air pumps are a different story, especially the store air pumps.
Rick Mileski Sr.
If your air pump is the one giving you trouble, see our guide to fixing a weak aquarium air pump.
Safety First
Always unplug a pump before you put your hands in the tank or take the pump apart. If a pump has a cracked case or a damaged cord, don’t put it back in the water. Throw it out and replace it.
Check 1: The Power
- Is the outlet working? Plug a lamp or phone charger into the same outlet.
- Did the GFCI outlet trip? Press the reset button. If it trips again as soon as you plug the pump back in, the pump is leaking electricity. Unplug it and replace it.
- Is the power strip or timer on? Check the switch, and check the timer settings if the pump runs on one.
- Check the drip loop. The cord should dip below the outlet before it goes up to the plug, so water runs off the bottom of the loop and not into the outlet.
Check 2: The Impeller
If the pump hums but doesn’t move water, the impeller is almost always stuck. Slime, sand, plant bits and snail shells settle around it, especially after the pump has been off for a while.
- Unplug the pump and take it out of the tank.
- Remove the front cover or intake to get to the impeller. Most powerheads twist or snap open.
- Pull out the impeller and wipe off the impeller, the magnet and the well it sits in. A soft brush or cotton swab works well.
- Remove white scale by soaking the impeller and cover in white vinegar for 10–15 minutes, then rinsing them well.
- Look for damage: broken fins, a cracked magnet or a bent or missing shaft. Some pumps have replacement impellers made for that model, which cost less than a new pump.
- Put it back together and test it in the tank.
AquaClear filters have the same kind of impeller. See how to fix a stuck AquaClear impeller.
Check 3: The Intake and Outlet
- Clogged intake screen or sponge. A dirty prefilter sponge or intake screen chokes the flow. Rinse the sponge in old tank water, never in tap water, so you don’t kill the good bacteria.
- Something stuck in the intake. Snails and small fish sometimes get pulled in. Unplug the pump and check.
- Kinked or clogged tubing. If the pump pushes water through a hose, check for kinks and gunk inside the hose.
- Running dry. A submersible pump must stay completely under water. If the water level dropped and it ran dry, it may have overheated. Top off the tank and try it again.
Still Dead? When to Replace It
Replace the pump if any of these are true:
- It doesn’t hum at all, even in an outlet you know works.
- It hums and gets hot, even with a clean impeller that spins freely by hand.
- It trips the GFCI every time you plug it in.
- The case is cracked or the cord is damaged.
Buy a pump with the same flow (gallons per hour, or GPH) as the old one, or check the tank size on the box. These are sold and shipped by Walmart:
- Powerhead for undergravel filters and circulation: Marineland Maxi-Jet 1200 Multi-Use Water Pump and Powerhead. It can also run a small fountain.
- More water movement for bigger tanks: Marineland Maxi-Jet Pro Pump, 160 to 750 GPH
If you’d rather stay with AquaClear, you can check AquaClear powerheads on Amazon.
Tip: Keep a spare pump or powerhead in your fish cabinet. If a pump dies on a weekend, you can swap it in right away.
Frequently Asked Questions
Why is my powerhead humming but not pumping water?
The impeller is stuck or the intake is clogged. Unplug it, clean the impeller and its well, and rinse the intake sponge in old tank water.
Can I fix a powerhead motor?
No. The motor is sealed in the case. You can clean or replace the impeller, but if the motor itself has failed, replace the pump.
Why does my GFCI trip when I plug in my pump?
The pump is probably leaking electricity into the water. Unplug it right away and replace it. Don’t keep resetting the GFCI.
How often should I clean my powerhead?
About once a month, or whenever you clean your filter. Clean it more often if you have sand or a lot of snails.
Written by Rick Mileski Sr., tropical fish keeper and breeder since the late 1960s and former owner of FinTastik Tropical Fish.
Sources and editorial notes: Product listings were checked in November 2026. Always follow the safety instructions that came with your pump.